 |
Video Amplifier using BC560 Schematic Diagram |
The video amplifier in the diagram is a well-known design. Simple, yet very useful, were it not for the ease with which the transistors can be damaged if the potentiometers (black level and signal amplitude) are in their extreme position. Fortunately, this can be obviated by the addition of two resistors. If in the diagram R3 and R4 were direct connections, as in the original design, and P1 were fully clockwise and P2 fully anticlockwise, such a large base current would flow through T1 that this transistor would give up the ghost.
Moreover, with the wiper of P2 at earth level, the base current of T2 would be dangerously high. Resistors R3 and R4 are sufficient protection against such mishaps, since they limit the base currents to a level of not more than 5 mA. Shunt capacitor C4 prevents R4 having an adverse effect on the amplification.
Author: L.A.M. Prins
Copyright: Elektor Electronics
Source: http://www.extremecircuits.net/2010/07/video-amplifier.html
Related Posts :
TDA2003 Car amplifierThis is a very popular series of amplifiers audio users who require maximum aduio results and of cou… Read More...
2,5 Watt audio amplifier circuit diagramThe above is a simple amplifier circuit also has a minimal power output. By using only a few compone… Read More...
2 X 40 Watt STK amplifierComponents of the above is one component of ic which is applied as a reinforcement. Power amplifier … Read More...
20W amplifier schematic with muteThis is a series of audio amplifier using ic and equipped with a mute switch. This circuit using ic … Read More...
140W audio amplifier with IC STK070By using the above amplifier circuit you can hear the sound quality is quite good by a high output p… Read More...
60W ICs amplifier with OM961Amplifier circuit is very suitable for use in car audio speakers that use a subwoofer, with a power … Read More...
20W Surround audio amplifier with SI-1020GHave you been use the IC above? if those who have not, IC above is used or applied to the audio powe… Read More...
Subowoofer audio car amplifierFor the a one amplifier circuit is very suitable for use in applications subwoofer speaker, which al… Read More...
Subwoofer amplifier with 30W output powerAmplifier circuit is very suitable for use in subwoofer amplifier system based on IC SI1030G. Amplfi… Read More...
2 X 30Watt home amplifier circuitAudio amplifier circuit is very suitable for use at home, using a subwoofer speaker, or woofer speak… Read More...
2W PA246 amplifier circuitThis amplifier output circuit having a fairly low at only 2W 8 ohm impedance. Minimum supply voltage… Read More...
70W STK amplifier schematicFor this amplifier circuit using three voltage plus, min, and the ground. with a maximum voltage app… Read More...
Stereo 30W STK ICs amplifier circuitThis amplifier circuit based on IC STK ic used in which the manifold. And on this circuit ic STK has… Read More...
Stereo STK013 audio amplifier circuitOn the amplifier circuit using ic STK, the same as my previous posting. However, in the above circui… Read More...
50W car audio amplifier schematic circuitsCar power amplifier uses SI1050GL IC as the main amplifier. The output power 50 Watt 8 ohm mono impe… Read More...
1000W ICs audio amplifier with PA03This is a series of amplifiers are based on the most high-ic power that I have ever known. Because t… Read More...
2 x 2,3 Watts power amplifier schematicsDo not misunderstand, this series is one of several series of power amplifiers that have output / lo… Read More...
Mini and simple power amplifier circuitsWhat is the meaning of the picture above? The above picture is a miniature audio amplifier and very … Read More...
6 - 12 Volt audio amplifier circuitsThe above is an amplifier circuit using supply voltages from 6 volts DC to 12 Volt DC. Power output … Read More...
50W audio amplifier with IC'sThe above amplifier circuit based on IC is STK075G, and another equation that is STK084G, STK085, ST… Read More...
0 Response to "Video Amplifier using BC560"
Post a Comment