A. Unable to start.
Can be caused by:
- No start-up voltage supply Vcc or a voltage less than 16V
- Electrolityc Capacitors supply voltage Vcc filter dry.
2. Led indicator blinking
If the supply voltage Vcc examined rocking. This is because the regulator of life and death because OVLO work., Die-protectionist regulators and auto start life over and over. If it is turned off Electrolityc Capacitors usually still keep the rest of the cargo.
Can be caused by:

- Electrolityc Capacitors supply voltage Vcc filter on a pin-4 dry. Replace with a value equal to or slightly larger. - triger UVLO
- input filter capacitor on pin-1 feed dry behind the declining value - triger OLP
- Rectifier diode of the switching transformer is damaged (sometimes when examined with avo-meter looks like a still good)
- cause the supply voltage Vcc drops of the switching transformer (UVLO)
- Part damage or broken lines on the feedback circuit of the voltage regulator through B to photocoupler - triger OVP
- Electrolityc Capacitors dry filter voltage B - triger OVP
- One of the output voltage of the switching transformer secondaries there is a short (over load) - triger OLP
- Soft start capacitor value decreases - triger OLP
3. Noise arising (noise)
Can be caused by:
- Transformer windings slack.
- If there are ceramic capacitors - can sometimes cause interference noise due to its characteristic piezoelectrik like crystal resonator. Replace with film capacitors.
4. When the st-by normal stress. But when the power is on the regulator directly off protectionism no voltage on the secondary this part. Electrolityc Capacitors are still storing charge.
Can be caused by:
- Sensor OVP small value resistor on pin-2 to the ground so that the value of delayed triger to OLP or OCP.
- Regulator IC is damaged
---------------------------------------------------------------------------------------------------------------------------
Note: Be careful when the regulator is not working. Because of Electrolityc Capacitors may still have a charge when turned off.
Related Posts :
The damage Horizontal LG TVOften find LG TV is switched off completely. After checking it Hor short TR / koslet so that all the… Read More...
Main function of TV tunerThe main function of the tuner is to select the RF signals from the desired frequency spectrum wave … Read More...
Understanding the workings of Vertical DeflectionVertical deflection parts, serves to provide a sawtooth current to the vertical deflection coil so t… Read More...
TDA9302 Vertical deflection output schematicsThe TDA9302H is a monolithic integrated circuit in HEPTAWATTTM package. This is a high efficiency po… Read More...
Treatment LCD monitorTreatment LCD Monitor. At this time computer use familiar and already widely used either for work or… Read More...
TV Vertical ProtectorsVertical Protectors (another term surge protector or Vertical CRT Neck Guard or protector) . If… Read More...
Process formation of RGB signal on TVBasically the UOC is equipped with RGB or YUV input from external, so it is possible to use the DVD … Read More...
Video IF circuit TVVideo IF circuitThe main function of the video IF is to change the 38.0 MHz IF signal into the CVBS … Read More...
NTSC-PAL TV Signal IdentifierThis circuit is able to identify PAL and NTSC video signals. Its output is high for an NTSC signal a… Read More...
Transformer ElectronicsTransformer (transformer) is the electrical / electronics that function to move energy (power) power… Read More...
IC LA78040 schematic for vertical deflectionSynchronization circuit to make the signals useful in the process of scanning of the transmitter and… Read More...
Vertical IC PIN-OUT DATAVertical Vin = input (non-inverted), Vout = Vertical output, VfB = Vertical feedback (inverted inppu… Read More...
Solving the problem on tv tunerTv tuner serves as the catcher signals from the antenna. Damage tuner, among others:1. Image does no… Read More...
X-Ray Protector CircuitsA protector system that is applied at the beginning of the television technique, therefore most ofte… Read More...
Switching Mode Power Supply using STRSwitching Power supply circuit produces a voltage B + (dc voltage) needed television series taken fr… Read More...
TV Protect Circuit Dead or Damaged ?Television set equipped with a circuit protector, then there are several possibilities that could oc… Read More...
Video Distribution AmplifierWith the amount of equipment during in entertainment centers at present the need to survive able to … Read More...
Universal switching power supply for TVThe schematic above can be used for supply on color TV for all type TV circuit. But we need to know … Read More...
Audio amplifier with IC AN7522, AN7523 and TDA2616The series of amplifiers that are used on the television audio, amplifier used amplifier ICs, includ… Read More...
Schematic diagram of switching power suplly for color television circuitSchematic diagram of switching power supply for color television , which can used on a particular co… Read More...
0 Response to "Troubleshooting STR IC Regulator Power Supply"
Post a Comment